Tplink utility

HigherLink to MIBs: device overview page: page (web): template was tested on:T2600G-28TS revision 2.0, version 2.0.0 Build 20170628 Rel.55184 (Beta)SetupRefer to the vendor documentation.Zabbix configurationNo specific Zabbix configuration is required.Macros usedNameDescriptionDefault{$CPU.UTIL.CRIT}-90{$MEMORY.UTIL.MAX}-90Template linksNameGeneric SNMPInterfaces Simple SNMPDiscovery rulesNameDescriptionTypeKey and additional infoCPU DiscoveryDiscovering TPLINK-SYSMONITOR-MIB::tpSysMonitorCpuTable, displays the CPU utilization of all UNITs.SNMPcpu.discoveryMemory DiscoveryDiscovering TPLINK-SYSMONITOR-MIB::tpSysMonitorMemoryTable, displays the memory utilization of all UNITs.SNMPmemory.discoveryItems collectedGroupNameDescriptionTypeKey and additional infoCPU#{#SNMPVALUE}: CPU utilizationMIB: TPLINK-SYSMONITOR-MIBDisplays the CPU utilization in 1 minute.Reference: model nameMIB: TPLINK-SYSINFO-MIBThe hardware version of the product.SNMPsystem.hw.modelPreprocessing:- DISCARD_UNCHANGED_HEARTBEAT: 1dInventoryHardware serial numberMIB: TPLINK-SYSINFO-MIBThe Serial number of the product.SNMPsystem.hw.serialnumberPreprocessing:- DISCARD_UNCHANGED_HEARTBEAT: 1dInventoryFirmware versionMIB: TPLINK-SYSINFO-MIBThe software version of the product.SNMPsystem.hw.firmwarePreprocessing:- DISCARD_UNCHANGED_HEARTBEAT: 1dInventoryHardware version(revision)MIB: TPLINK-SYSINFO-MIBThe hardware version of the product.SNMPsystem.hw.versionPreprocessing:- DISCARD_UNCHANGED_HEARTBEAT: 1dMemory#{#SNMPVALUE}: Memory utilizationMIB: TPLINK-SYSMONITOR-MIBDisplays the memory utilization.Reference: and additional info#{#SNMPVALUE}: High CPU utilization (over {$CPU.UTIL.CRIT}% for 5m)CPU utilization is too high. The system might be slow to respond.min(/TP-LINK SNMP/system.cpu.util[tpSysMonitorCpu1Minute.{#SNMPINDEX}],5m)>{$CPU.UTIL.CRIT}WARNINGDevice has been replaced (new serial number received)Device serial number has changed. Ack to closelast(/TP-LINK SNMP/system.hw.serialnumber,#1)last(/TP-LINK SNMP/system.hw.serialnumber,#2) and length(last(/TP-LINK SNMP/system.hw.serialnumber))>0INFOManual close: YESFirmware has changedFirmware version has changed. Ack to closelast(/TP-LINK SNMP/system.hw.firmware,#1)last(/TP-LINK SNMP/system.hw.firmware,#2) and length(last(/TP-LINK SNMP/system.hw.firmware))>0INFOManual close: YES#{#SNMPVALUE}: High memory utilization (>{$MEMORY.UTIL.MAX}% for 5m)The system is running out of free memory.min(/TP-LINK SNMP/vm.memory.util[tpSysMonitorMemoryUtilization.{#SNMPINDEX}],5m)>{$MEMORY.UTIL.MAX}AVERAGEFeedbackPlease report any issues with the template at IssuesDescription: Default sysLocation, sysName and sysContact is not filled with proper data. Real hostname and location can be found only in private branch (TPLINK-SYSINFO-MIB). Please check whether this problem exists in the latest firmware: 2.0.0 Build 20170628 Rel.55184 (Beta)Device: T2600G-28TS 2.0Description: The Serial number of the product (tpSysInfoSerialNum) is missing in HW versions prior to V2_170323Version: Prior to version V2_170323Device: T2600G-28TS 2.0 This template is for Zabbix version: 5.0 Source: Template Net TP-LINK SNMPOverviewFor Zabbix version: 5.0 and higherLink to MIBs: device overview page: page (web): template was tested on:T2600G-28TS revision 2.0, version 2.0.0 Build 20170628 Rel.55184 (Beta)SetupRefer to the vendor documentation.Zabbix configurationNo specific Zabbix configuration is required.Macros usedNameDescriptionDefault{$CPU.UTIL.CRIT}-90{$MEMORY.UTIL.MAX}-90Template linksNameGeneric SNMPInterfaces Simple SNMPDiscovery rulesNameDescriptionTypeKey and additional infoCPU DiscoveryDiscovering TPLINK-SYSMONITOR-MIB::tpSysMonitorCpuTable, displays the CPU utilization of all UNITs.SNMPcpu.discoveryMemory DiscoveryDiscovering TPLINK-SYSMONITOR-MIB::tpSysMonitorMemoryTable, displays the memory utilization of all UNITs.SNMPmemory.discoveryItems collectedGroupNameDescriptionTypeKey and additional infoCPU#{#SNMPVALUE}: CPU utilizationMIB: TPLINK-SYSMONITOR-MIBDisplays the CPU utilization in 1 minute.Reference: model nameMIB: TPLINK-SYSINFO-MIBThe hardware version of the product.SNMPsystem.hw.modelPreprocessing:- DISCARD_UNCHANGED_HEARTBEAT: 1dInventoryHardware serial numberMIB: TPLINK-SYSINFO-MIBThe Serial number of the product.SNMPsystem.hw.serialnumberPreprocessing:- DISCARD_UNCHANGED_HEARTBEAT: 1dInventoryFirmware versionMIB: TPLINK-SYSINFO-MIBThe software version of the product.SNMPsystem.hw.firmwarePreprocessing:- DISCARD_UNCHANGED_HEARTBEAT: 1dInventoryHardware version(revision)MIB: TPLINK-SYSINFO-MIBThe hardware version of the product.SNMPsystem.hw.versionPreprocessing:- DISCARD_UNCHANGED_HEARTBEAT: 1dMemory#{#SNMPVALUE}: Memory utilizationMIB: TPLINK-SYSMONITOR-MIBDisplays the memory utilization.Reference: and additional info#{#SNMPVALUE}: High CPU utilization (over {$CPU.UTIL.CRIT}% for 5m)CPU utilization is too high. The

Utilization of all UNITs.SNMPcpu.discoveryMemory DiscoveryDiscovering TPLINK-SYSMONITOR-MIB::tpSysMonitorMemoryTable, displays the memory utilization of all UNITs.SNMPmemory.discoveryNetwork interfaces discoveryDiscovering interfaces from IF-MIB.SNMPnet.if.discoveryFilter:AND - {#IFADMINSTATUS} MATCHES_REGEX {$NET.IF.IFADMINSTATUS.MATCHES}- {#IFADMINSTATUS} NOT_MATCHES_REGEX {$NET.IF.IFADMINSTATUS.NOT_MATCHES}- {#IFOPERSTATUS} MATCHES_REGEX {$NET.IF.IFOPERSTATUS.MATCHES}- {#IFOPERSTATUS} NOT_MATCHES_REGEX {$NET.IF.IFOPERSTATUS.NOT_MATCHES}- {#IFNAME} MATCHES_REGEX {$NET.IF.IFNAME.MATCHES}- {#IFNAME} NOT_MATCHES_REGEX {$NET.IF.IFNAME.NOT_MATCHES}- {#IFDESCR} MATCHES_REGEX {$NET.IF.IFDESCR.MATCHES}- {#IFDESCR} NOT_MATCHES_REGEX {$NET.IF.IFDESCR.NOT_MATCHES}- {#IFTYPE} MATCHES_REGEX {$NET.IF.IFTYPE.MATCHES}- {#IFTYPE} NOT_MATCHES_REGEX {$NET.IF.IFTYPE.NOT_MATCHES}Items collectedGroupNameDescriptionTypeKey and additional infoCPU#{#SNMPVALUE}: CPU utilizationMIB: TPLINK-SYSMONITOR-MIBDisplays the CPU utilization in 1 minute.Reference: traps (fallback)The item is used to collect all SNMP traps unmatched by other snmptrap itemsSNMP_TRAPsnmptrap.fallbackGeneralSystem locationMIB: SNMPv2-MIBThe physical location of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string.SNMPsystem.location[sysLocation.0]Preprocessing:- DISCARD_UNCHANGED_HEARTBEAT: 12hGeneralSystem contact detailsMIB: SNMPv2-MIBThe textual identification of the contact person for this managed node, together with information on how to contact this person. If no contact information is known, the value is the zero-length string.SNMPsystem.contact[sysContact.0]Preprocessing:- DISCARD_UNCHANGED_HEARTBEAT: 12hGeneralSystem object IDMIB: SNMPv2-MIBThe vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determiningwhat kind of box' is being managed. For example, if vendorFlintstones, Inc.' was assigned the subtree1.3.6.1.4.1.4242, it could assign the identifier 1.3.6.1.4.1.4242.1.1 to its `Fred Router'.SNMPsystem.objectid[sysObjectID.0]Preprocessing:- DISCARD_UNCHANGED_HEARTBEAT: 12hGeneralSystem nameMIB: SNMPv2-MIBAn administratively-assigned name for this managed node.By convention, this is the node's fully-qualified domain name. If the name is unknown, the value is the zero-length string.SNMPsystem.namePreprocessing:- DISCARD_UNCHANGED_HEARTBEAT: 12hGeneralSystem descriptionMIB: SNMPv2-MIBA textual description of the entity. This value shouldinclude the full name and version identification of the system's hardware type, software operating-system, andnetworking software.SNMPsystem.descr[sysDescr.0]Preprocessing:- DISCARD_UNCHANGED_HEARTBEAT: 12hInventoryHardware model nameMIB: TPLINK-SYSINFO-MIBThe hardware version of the product.SNMPsystem.hw.modelPreprocessing:- DISCARD_UNCHANGED_HEARTBEAT: 1dInventoryHardware serial numberMIB: TPLINK-SYSINFO-MIBThe Serial number of the product.SNMPsystem.hw.serialnumberPreprocessing:- DISCARD_UNCHANGED_HEARTBEAT: 1dInventoryFirmware versionMIB: TPLINK-SYSINFO-MIBThe software version of the product.SNMPsystem.hw.firmwarePreprocessing:- DISCARD_UNCHANGED_HEARTBEAT: 1dInventoryHardware version(revision)MIB: TPLINK-SYSINFO-MIBThe hardware version of the product.SNMPsystem.hw.versionPreprocessing:- DISCARD_UNCHANGED_HEARTBEAT: 1dMemory#{#SNMPVALUE}: Memory utilizationMIB: TPLINK-SYSMONITOR-MIBDisplays the memory utilization.Reference: interfacesInterface {#IFDESCR}: Operational statusMIB: IF-MIBThe current operational state of the interface.- The testing(3) state indicates that no operational packet scan be passed- If ifAdminStatus is down(2) then ifOperStatus should be down(2)- If ifAdminStatus is changed to up(1) then ifOperStatus should change to up(1) if the interface is ready to transmit and receive network traffic- It should change todormant(5) if the interface is waiting for external actions (such as a serial line waiting for an incoming connection)- It should remain in the down(2) state if and only if there is a fault that prevents it from going to the up(1) state- It

TP-Link Technologies Co., Ltd., is a Chinese manufacturer of computer networking products based. Available solutions TP-LINK SNMP 3rd party solutions This template is for Zabbix version: 7.2 Source: TP-LINK by SNMPOverviewLink to MIBs: device overview page: page (web): issuesDescription: 'Default sysLocation, sysName and sysContact is not filled with proper data. Real hostname and location can be found only in private branch (TPLINK-SYSINFO-MIB). Please check whether this problem exists in the latest firmware: 2.0.0 Build 20170628 Rel.55184 (Beta)device: T2600G-28TS 2.0Description: The Serial number of the product (tpSysInfoSerialNum) is missing in HW versions prior to V2_170323version: Prior to version V2_170323device: T2600G-28TS 2.0RequirementsZabbix version: 7.2 and higher.Tested versionsThis template has been tested on:T2600G-28TS revision 2.0 2.0.0 Build 20170628 Rel.55184 (Beta)ConfigurationZabbix should be configured according to the instructions in the Templates out of the box section.SetupRefer to the vendor documentation.Macros usedNameDescriptionDefault{$MEMORY.UTIL.MAX}90{$CPU.UTIL.CRIT}90{$SNMP.TIMEOUT}Time interval for the SNMP availability trigger.5m{$ICMP_LOSS_WARN}Warning threshold of ICMP packet loss in %.20{$ICMP_RESPONSE_TIME_WARN}Warning threshold of the average ICMP response time in seconds.0.15{$IFCONTROL}1{$IF.UTIL.MAX}95{$NET.IF.IFNAME.MATCHES}^.*${$NET.IF.IFNAME.NOT_MATCHES}Filter out loopbacks, nulls, docker veth links and docker0 bridge by defaultMacro too long. Please see the template.{$NET.IF.IFOPERSTATUS.MATCHES}^.*${$NET.IF.IFOPERSTATUS.NOT_MATCHES}Ignore notPresent(6)^6${$NET.IF.IFADMINSTATUS.MATCHES}^.*{$NET.IF.IFADMINSTATUS.NOT_MATCHES}Ignore down(2) administrative status^2${$NET.IF.IFDESCR.MATCHES}.*{$NET.IF.IFDESCR.NOT_MATCHES}CHANGE_IF_NEEDED{$NET.IF.IFTYPE.MATCHES}.*{$NET.IF.IFTYPE.NOT_MATCHES}CHANGE_IF_NEEDED{$NET.IF.IFALIAS.MATCHES}.*{$NET.IF.IFALIAS.NOT_MATCHES}CHANGE_IF_NEEDED{$IF.ERRORS.WARN}Warning threshold of error packet rate. Can be used with interface name as context.2ItemsNameDescriptionTypeKey and additional infoHardware model nameMIB: TPLINK-SYSINFO-MIBThe hardware version of the product.SNMP agentsystem.hw.modelPreprocessingDiscard unchanged with heartbeat: 1dHardware serial numberMIB: TPLINK-SYSINFO-MIBThe Serial number of the product.SNMP agentsystem.hw.serialnumberPreprocessingDiscard unchanged with heartbeat: 1dFirmware versionMIB: TPLINK-SYSINFO-MIBThe software version of the product.SNMP agentsystem.hw.firmwarePreprocessingDiscard unchanged with heartbeat: 1dHardware version(revision)MIB: TPLINK-SYSINFO-MIBThe hardware version of the product.SNMP agentsystem.hw.versionPreprocessingDiscard unchanged with heartbeat: 1dSNMP walk system CPUsDiscovering TPLINK-SYSMONITOR-MIB::tpSysMonitorCpuTable, displays the CPU utilization of all UNITs.SNMP agentsystem.cpu.walkSNMP walk memoryDiscovering TPLINK-SYSMONITOR-MIB::tpSysMonitorMemoryTable, displays the memory utilization of all UNITs.SNMP agentvm.memory.walkUptime (network)MIB: SNMPv2-MIBTime (in hundredths of a second) since the network management portion of the system was last re-initialized.SNMP agentsystem.net.uptime[sysUpTime.0]PreprocessingCustom multiplier: 0.01Uptime (hardware)MIB: HOST-RESOURCES-MIBThe amount of time since this host was last initialized. Note that this is different from sysUpTime in the SNMPv2-MIB [RFC1907] because sysUpTime is the uptime of the network management portion of the system.SNMP agentsystem.hw.uptime[hrSystemUptime.0]PreprocessingCheck for not supported value: any error⛔️Custom on fail: Set value to: 0Custom multiplier: 0.01SNMP traps (fallback)The item is used to collect all SNMP traps unmatched by other snmptrap itemsSNMP trapsnmptrap.fallbackSystem locationMIB: SNMPv2-MIBPhysical location of the node (e.g., equipment room, 3rd floor). If not provided, the value is a zero-length string.SNMP agentsystem.location[sysLocation.0]PreprocessingDiscard unchanged with heartbeat: 12hSystem contact detailsMIB: SNMPv2-MIBThe textual identification of the contact person for this managed node, together with information on how to

SNMP/net.if.out.errors[ifOutErrors.{#SNMPINDEX}],5m)>{$IF.ERRORS.WARN:"{#IFNAME}"}WarningManual close: YesDepends on:TP-LINK: Interface {#IFNAME}({#IFALIAS}): Link downTP-LINK: Interface {#IFNAME}({#IFALIAS}): Ethernet has changed to lower speed than it was beforeThis Ethernet connection has transitioned down from its known maximum speed. This might be a sign of autonegotiation issues. Acknowledge to close the problem manually.change(/TP-LINK by SNMP/net.if.speed[ifSpeed.{#SNMPINDEX}])0 and ( last(/TP-LINK by SNMP/net.if.type[ifType.{#SNMPINDEX}])=6 or last(/TP-LINK by SNMP/net.if.type[ifType.{#SNMPINDEX}])=7 or last(/TP-LINK by SNMP/net.if.type[ifType.{#SNMPINDEX}])=11 or last(/TP-LINK by SNMP/net.if.type[ifType.{#SNMPINDEX}])=62 or last(/TP-LINK by SNMP/net.if.type[ifType.{#SNMPINDEX}])=69 or last(/TP-LINK by SNMP/net.if.type[ifType.{#SNMPINDEX}])=117 ) and (last(/TP-LINK by SNMP/net.if.status[ifOperStatus.{#SNMPINDEX}])2)InfoManual close: YesDepends on:TP-LINK: Interface {#IFNAME}({#IFALIAS}): Link downFeedbackPlease report any issues with the template at can also provide feedback, discuss the template, or ask for help at ZABBIX forums This template is for Zabbix version: 6.4 Source: TP-LINK by SNMPOverviewLink to MIBs: device overview page: page (web): issuesDescription: 'Default sysLocation, sysName and sysContact is not filled with proper data. Real hostname and location can be found only in private branch (TPLINK-SYSINFO-MIB). Please check whether this problem exists in the latest firmware: 2.0.0 Build 20170628 Rel.55184 (Beta)device: T2600G-28TS 2.0Description: The Serial number of the product (tpSysInfoSerialNum) is missing in HW versions prior to V2_170323version: Prior to version V2_170323device: T2600G-28TS 2.0RequirementsZabbix version: 6.4 and higher.Tested versionsThis template has been tested on:T2600G-28TS revision 2.0 2.0.0 Build 20170628 Rel.55184 (Beta)ConfigurationZabbix should be configured according to the instructions in the Templates out of the box section.SetupRefer to the vendor documentation.Macros usedNameDescriptionDefault{$MEMORY.UTIL.MAX}90{$CPU.UTIL.CRIT}90{$SNMP.TIMEOUT}5m{$ICMP_LOSS_WARN}20{$ICMP_RESPONSE_TIME_WARN}0.15{$IFCONTROL}1{$IF.UTIL.MAX}95{$NET.IF.IFNAME.MATCHES}^.*${$NET.IF.IFNAME.NOT_MATCHES}Filter out loopbacks, nulls, docker veth links and docker0 bridge by defaultMacro too long. Please see the template.{$NET.IF.IFOPERSTATUS.MATCHES}^.*${$NET.IF.IFOPERSTATUS.NOT_MATCHES}Ignore notPresent(6)^6${$NET.IF.IFADMINSTATUS.MATCHES}^.*{$NET.IF.IFADMINSTATUS.NOT_MATCHES}Ignore down(2) administrative status^2${$NET.IF.IFDESCR.MATCHES}.*{$NET.IF.IFDESCR.NOT_MATCHES}CHANGE_IF_NEEDED{$NET.IF.IFTYPE.MATCHES}.*{$NET.IF.IFTYPE.NOT_MATCHES}CHANGE_IF_NEEDED{$NET.IF.IFALIAS.MATCHES}.*{$NET.IF.IFALIAS.NOT_MATCHES}CHANGE_IF_NEEDED{$IF.ERRORS.WARN}2ItemsNameDescriptionTypeKey and additional infoTP-LINK: Hardware model nameMIB: TPLINK-SYSINFO-MIBThe hardware version of the product.SNMP agentsystem.hw.modelPreprocessingDiscard unchanged with heartbeat: 1dTP-LINK: Hardware serial numberMIB: TPLINK-SYSINFO-MIBThe Serial number of the product.SNMP agentsystem.hw.serialnumberPreprocessingDiscard unchanged with heartbeat: 1dTP-LINK: Firmware versionMIB: TPLINK-SYSINFO-MIBThe software version of the product.SNMP agentsystem.hw.firmwarePreprocessingDiscard unchanged with heartbeat: 1dTP-LINK: Hardware version(revision)MIB: TPLINK-SYSINFO-MIBThe hardware version of the product.SNMP agentsystem.hw.versionPreprocessingDiscard unchanged with heartbeat: 1dTP-LINK: SNMP walk system CPUsDiscovering TPLINK-SYSMONITOR-MIB::tpSysMonitorCpuTable, displays the CPU utilization of all UNITs.SNMP agentsystem.cpu.walkTP-LINK: SNMP walk memoryDiscovering TPLINK-SYSMONITOR-MIB::tpSysMonitorMemoryTable, displays the memory utilization of all UNITs.SNMP agentvm.memory.walkTP-LINK: Uptime (network)MIB: SNMPv2-MIBThe time (in hundredths of a second) since the network management portion of the system was last re-initialized.SNMP agentsystem.net.uptime[sysUpTime.0]PreprocessingCustom multiplier: 0.01TP-LINK: Uptime (hardware)MIB: HOST-RESOURCES-MIBThe amount of time since this host was last initialized. Note that this is different from sysUpTime in the SNMPv2-MIB [RFC1907] because sysUpTime is the uptime of the network management portion of the system.SNMP agentsystem.hw.uptime[hrSystemUptime.0]PreprocessingCheck for not supported value⛔️Custom on fail: Set value to: 0Custom multiplier: 0.01TP-LINK: SNMP traps (fallback)The item